Nissan 200SX S13 silhouetteS13

Torque Specifications

All fastener torque values from the service manual, grouped by section — 396 component specs across 17 sections, plus 24 standard bolt references

396 specs

General Information

GI5 specs
Copper washerGI-5
17 - 20N·m
Air bleederGI-5
7 - 9N·m
Pin boltGI-5
22 - 31N·m
Cylinder bodyGI-5
54 - 64N·m
Pad retainer boltGI-5
54 - 64N·m

Example illustration

Maintenance

MA29 specs
Drain plugMA-13
54 - 74N·m

Apply sealant to thread

Fuel hose clampsMA-15
1.0 - 1.5N·m

All rubber hose clamps

Drain plugMA-16
29 - 39N·m

Install with new washer

Spark plugMA-18
20 - 29N·m

Model with catalyzer, Platinum-tipped type

Filler plugMA-21
25 - 34N·m

M/T filler plug

Drain plugMA-22
25 - 34N·m

M/T drain plug

Oil capacity (With torque converter)MA-23
7.9N·m

With torque converter

Filler plugMA-23
59 - 98N·m

Filler plug

Drain plugMA-23
59 - 98N·m

Drain plug

Wheel nutsMA-26
98 - 118N·m
Anchor boltMA-27
24 - 31N·m
Oil pan drain plugMA-29
29 - 39N·m
Spark plugMA-29
20 - 29N·m
Crank angle sensorMA-29
7 - 8N·m
Crankshaft pulleyMA-29
142 - 152N·m
Timing belt tensioner pulley nutMA-29
22 - 29N·m
Clutch — Pedal stopper lock nutMA-31
16 - 22N·m
Clutch — Clutch switch lock nutMA-31
12 - 15N·m
Manual transmission — Drain and filler plugsMA-31
25 - 34N·m
Final drive — Drain plugMA-31
59 - 98N·m
Final drive — Filler plugMA-31
59 - 98N·m
Front axle and front suspension — Tie-rod lock nutMA-31
37 - 46N·m
Front axle and front suspension — Camber adjusting pinMA-31
124 - 143N·m
Rear axle and rear suspension — Toe adjusting pinMA-31
69 - 88N·m
Rear axle and rear suspension — Camber adjusting pinMA-31
69 - 88N·m
Brake system — Air bleed valveMA-31
7 - 9N·m
Brake system — Brake lamp switch lock nutMA-31
12 - 15N·m
Brake system — Brake booster input rod lock nutMA-31
16 - 22N·m
Wheel and tire — Wheel nutMA-31
98 - 118N·m

Engine Mechanical

EM69 specs
Intake manifold collector boltsEM-5
20 - 25N·m
Throttle chamber boltsEM-5
18 - 22N·m
Collector cover boltsEM-5
16 - 21N·m
Fuel tube boltsEM-5
7 - 8N·m
Air regulator boltsEM-5
8.3N·m
A.A.C. valve boltsEM-5
8.3N·m
Fuel injector bolts (intake manifold)EM-5
20 - 25N·m
Stay boltsEM-5
2 - 4N·m
Rocker cover bolts (upper)EM-5
10 - 12N·m
Alternator boltsEM-5
14 - 17N·m
Alternator pivot boltEM-5
49 - 59N·m
Crank angle sensor boltsEM-5
7 - 8N·m
Crankshaft pulley bolt (with washer)EM-5
142 - 152N·m
Center bolt (lower area)EM-5
37 - 48N·m
Spark plugEM-5
20 - 29N·m
Exhaust gas sensor (catalyzer model only)EM-5
40 - 50N·m
Lock plate boltsEM-5
25 - 39N·m
Oil pressure switch / Oil filter area boltsEM-5
30 - 40N·m
Crank angle sensorEM-9
14 - 19N·m
Tensioner pulleyEM-9
22 - 29N·m
Idler pulleyEM-9
31 - 42N·m
Front timing belt coverEM-9
7 - 8N·m
Crankshaft pulley boltEM-9
142 - 152N·m
Crank angle sensor boltEM-9
14 - 19N·m
Front timing belt cover boltEM-9
7 - 8N·m
Tensioner pulley boltEM-9
22 - 29N·m
Idler pulley boltEM-9
31 - 42N·m
Cam bracket boltEM-16
10 - 12N·m
Camshaft oil seal lip bolt torque (camshaft bracket bolts)EM-25
9 - 12N·m

Camshaft bracket bolt torque

Camshaft bracket boltEM-25
≈8.8 - 12N·m

Camshaft bracket bolt torque

Rear timing cover boltEM-25
7 - 8N·m

Rear timing cover

Tensioner nutEM-25
22 - 29N·m

Timing belt tensioner nut

Sprocket boltEM-26
14 - 19N·m

Camshaft sprocket installation

Cylinder head bolt torque — Step 1EM-27
29N·m

Initial tighten, numerical order

Cylinder head bolt torque — Step 2EM-27
103N·m

Second tighten, numerical order

Cylinder head bolt torque — Step 4EM-27
29N·m

After loosening completely, numerical order

Cylinder head bolt torque — Step 5EM-27
103N·m

Final torque, or angle tighten 85–90 degrees clockwise

Air inlet pipe bolts (upper area, right side)EM-28
16 - 21N·m
Oil delivery tube / water tube upper boltsEM-28
6.3 - 8.3N·m
Water outlet tube bolts (upper)EM-28
11 - 15N·m
Oil delivery tube bolts (lower left)EM-28
6.3 - 8.3N·m
Oil delivery tube bolts (middle left)EM-28
6.3 - 8.3N·m
Turbocharger mounting nutsEM-28
25 - 39N·m
Exhaust gas sensor (catalyzer model only)EM-28
40 - 50N·m
Exhaust outlet flange bolts (upper)EM-28
22 - 29N·m
Exhaust outlet flange bolts (lower)EM-28
22 - 29N·m
Oil return tube bolts (lower center)EM-28
13 - 16N·m
Oil return tube / lower left boltsEM-28
11 - 15N·m
Lower left bracket boltsEM-28
11 - 15N·m
Fastener torque (mount bracket upper)EM-31
22 - 28N·m

Engine mount bracket upper bolts (left side upper)

Fastener torque (mount bracket)EM-31
43 - 55N·m

Engine mount bracket bolts (multiple locations)

Fastener torque (mount bracket upper right)EM-31
43 - 55N·m

Right side upper bracket

Fastener torque (engine mount to bracket)EM-31
22 - 26N·m

Right side engine mount to bracket

Fastener torque (engine mount insulator right)EM-31
22 - 28N·m

Right side engine mount insulator bolts

Fastener torque (engine mount insulator right lower)EM-31
43 - 55N·m

Right side engine mount insulator lower

Fastener torque (left side engine hanger bracket)EM-31
18 - 27N·m

Left side engine hanger bracket bolt

Fastener torque (transmission mount bracket small bolts)EM-31
16 - 21N·m

Transmission/gearbox mount bracket small bolts

Fastener torque (transmission mount bracket large bolts)EM-31
30 - 40N·m

Transmission/gearbox mount bracket large bolts

Fastener torque (rear mount bracket small)EM-31
16 - 21N·m

Rear mount bracket small bolts

Fastener torque (rear mount bracket lower)EM-31
43 - 55N·m

Rear mount bracket lower bolts

Fastener torque (rear mount insulator lower)EM-31
43 - 55N·m

Rear mount insulator lower bolts

Rear oil seal retainer boltsEM-33
7 - 10N·m
Flywheel (M/T) / Drive plate (A/T) boltsEM-33
98 - 108N·m
Connecting rod bearing cap boltsEM-33
41 - 44N·m
Oil pump boltsEM-33
11 - 14N·m
Main bearing beam boltsEM-33
44 - 54N·m
Oil strainer boltsEM-33
11 - 14N·m
Oil pan boltsEM-33
7 - 8N·m
Drain plugEM-33
29 - 39N·m

Engine Lubrication & Cooling Systems

LC28 specs
Oil pressure switchLC-4
10 - 16N·m
Oil pump fastenerLC-4
11 - 14N·m
CoverLC-5
4-5N·m
CapLC-5
39-69N·m
Cover boltLC-5
4 - 5N·m
Regulator valve capLC-5
39 - 69N·m
Oil jet boltLC-6
29 - 39N·m
Oil inlet tube boltLC-6
16 - 24N·m
Oil inlet tube (small bolt)LC-6
6.3 - 8.3N·m
Turbocharger mounting boltLC-6
16 - 24N·m
Oil outlet tube boltLC-6
13 - 16N·m
Oil cooler studLC-7
29-34N·m
Mounting bolt (oil cooler support)LC-7
21N·m
Oil cooler support boltLC-7
21N·m
Water pump mounting boltLC-8
16 - 20N·m
Thermostat housing boltLC-9
18 - 22N·m
Radiator capLC-10
6.3 - 8.3N·m
Radiator shroudLC-10
3.2 - 4.2N·m
Radiator cap fastenerLC-10
6.3 - 8.3N·m
Radiator shroud fastenerLC-10
3.2 - 4.2N·m
Oil cooler securing nutLC-11
8 - 12N·m
Fan to fan coupling boltLC-14
6 - 10N·m

Fan coupling to fan

Fan coupling to water pump pulley boltLC-14
6 - 10N·m

Fan coupling to water pump pulley

Water inlet tube bracket boltLC-14
11 - 15N·m

Water inlet tube bracket bolts

Water inlet tube fittingLC-14
11 - 15N·m

Water inlet tube fittings

Water outlet tube upper fittingLC-14
16 - 21N·m

Water outlet tube upper fittings

Water outlet tube lower fittingLC-14
16 - 21N·m

Water outlet tube lower fittings

Turbocharger water tube center bracket boltLC-14
11 - 15N·m

Center bracket bolts

Engine Fuel & Emission Control System

EF & EC1 spec
Fuel tube assembly fixing boltEF & EC-130
7 - 8N·m

Engine Control, Fuel & Exhaust System

FE25 specs
Torque — cable bracket / adjuster area (upper)FE-2
3 - 4N·m

Upper cable end torque

Torque — kickdown switch mounting boltsFE-2
8 - 12N·m

Kickdown switch bracket

Torque — kickdown switch / pedal area (lower right)FE-2
3 - 4N·m
Torque — throttle drum adjusting nutFE-2
8 - 11N·m

Throttle drum end

Torque — lock nut at pedal / kickdown areaFE-2
8 - 12N·m

Lock nut at pedal end

Fuel pump assembly mounting screwsFE-3
2.0 - 2.5N·m
Fuel filler neck clamp / hose clamp torque (upper area)FE-3
3.2 - 4.3N·m
Fuel tank mounting bolt torque (front/lower left)FE-3
26 - 36N·m
Fuel tank mounting bolt torque (rear/lower right)FE-3
26 - 36N·m
Fuel tank protector bolt torque (right side)FE-3
3.2 - 4.3N·m
Bracket/insulator nuts — model with catalyzer, upper catalyzer inletFE-4
5 - 7N·m

Model with catalyzer

Catalyzer flange bolts to front pipeFE-4
13 - 16N·m

Model with catalyzer

Front tube flange bolts (mid section)FE-4
5 - 7N·m

Model with catalyzer

Front tube flange bolts (lower section)FE-4
43 - 55N·m

Model with catalyzer

Front tube bracket boltsFE-4
5 - 7N·m

Model with catalyzer

Front tube to exhaust manifold nutsFE-4
45 - 60N·m

Model with catalyzer

Muffler hanger bracket bolts (rear left)FE-4
13 - 16N·m

Model with catalyzer

Muffler hanger bracket bolts (rear right)FE-4
13 - 16N·m

Model with catalyzer

Muffler flange boltsFE-4
43 - 55N·m

Model with catalyzer

Front tube upper bracket nuts — model without catalyzerFE-4
13 - 16N·m

Model without catalyzer

Front tube to exhaust manifold nuts — model without catalyzerFE-4
45 - 60N·m

Model without catalyzer

Muffler hanger bracket bolts (rear left) — model without catalyzerFE-4
13 - 16N·m

Model without catalyzer

Muffler hanger bracket bolts (rear right) — model without catalyzerFE-4
13 - 16N·m

Model without catalyzer

Muffler flange bolts — model without catalyzerFE-4
43 - 55N·m

Model without catalyzer

Front tube bracket bolts — model without catalyzer (additional location)FE-4
5 - 7N·m

Model with catalyzer, front tube area

Clutch

CL15 specs
Pedal bracket boltCL-4
16 - 22N·m
Return spring / clutch pedal boltCL-4
8 - 11N·m
Lock nutCL-4
16 - 22N·m
Clutch master cylinder mounting boltCL-4
8 - 11N·m
Operating cylinder boltCL-4
6 - 10N·m
Operating cylinder pipe/hose fittingCL-4
17 - 20N·m
Operating cylinder mounting bolt torque (upper)CL-4
30 - 40N·m
Operating cylinder small boltCL-4
8 - 11N·m
Bleeder screwCL-4
6 - 10N·m
Lock nutCL-5
8 - 11N·m

Lock nut

Pedal stopper lock nutCL-5
16 - 22N·m

Pedal stopper lock nut

Valve stopperCL-6
1.5 - 2.9N·m
Lock nutCL-6
8 - 11N·m
Bleeder screwCL-7
6 - 10N·m
Clutch cover securing boltCL-10
22 - 29N·m

Manual Transmission

MT25 specs
Transmission Bolt Torques — 1MT-5
39 - 49N·m
Transmission Bolt Torques — 2MT-5
39 - 49N·m
Transmission Bolt Torques — 3MT-5
39 - 49N·m
Transmission Bolt Torques — 4MT-5
29 - 39N·m
Transmission Bolt Torques — 5MT-5
29 - 39N·m
Transmission Bolt Torques — Gusset to engineMT-5
29 - 39N·m
Reverse check sleeveMT-6
4 - 5N·m
Rear extension boltsMT-6
16 - 20N·m
Bearing retainer boltsMT-6
19 - 25N·m
Filler plugMT-6
25 - 34N·m
Drain plugMT-6
25 - 34N·m
Neutral switchMT-6
20 - 29N·m

Thread of bolts

Reverse lamp switchMT-6
20 - 29N·m

Thread of bolts

Front cover boltsMT-6
20 - 34N·m
Front coverMT-6
16 - 21N·m

Thread of bolts

Mainshaft lock nutMT-7
137-167N·m
Countershaft lock nutMT-7
98-127N·m
Mainshaft lock nutMT-8
137-167N·m
Countershaft lock nutMT-8
98-127N·m
Return spring plugMT-9
20 - 29N·m
Check ball plugMT-9
19 - 25N·m
Check ball plug M8 boltMT-9
14 - 18N·m

M8 bolt

Check ball plug M12 boltMT-9
20 - 29N·m

M12 bolt

Striking lever retaining pinMT-9
9 - 12N·m
O.D. & reverse shift fork boltMT-9
49 - 59N·m

Automatic Transmission

AT12 specs
Lock nutAT-9
11 - 15N·m

Lock nut Y, Manual Control Linkage

Distance 'A' (torque converter to transmission)AT-75
23.5 or moreN·m

When connecting torque converter to transmission

transmission — 1AT-75
39 - 49N·m
transmission — 2AT-75
39 - 49N·m
transmission — 3AT-75
39 - 49N·m
transmission — 4AT-75
29 - 39N·m
transmission — 5AT-75
29 - 39N·m
transmission — Gusset to engineAT-75
29 - 39N·m
Torque — bolts (main housing, unlabeled group)AT-NC-1
61 - 64N·m
Torque — Bolt with flange headAT-NC-1
44 - 59N·m
Torque — Bolt without flangeAT-NC-1
39 - 49N·m
Torque — small fastener groupAT-NC-1
16 - 21N·m

Propeller Shaft & Differential Carrier

PD19 specs
Rear cover boltPD-11
88 - 118N·m
Filler plugPD-11
59 - 98N·m
Drain plugPD-11
59 - 98N·m
Ring gear boltPD-11
111 - 127N·m
Pinion front bearing preload / bearing cap boltPD-11
132 - 152N·m
Bearing cap bolt torque (differential case)PD-11
88 - 98N·m
Companion flange nutPD-11
186 - 294N·m
Total preloadPD-12
1.4 - 1.7N·m
Drive pinion nut preload (with Dummy Shaft)PD-17
1.3N·m

Step 4

Pinion bearing preloadPD-26
1.1 - 1.4N·m
Differential oil cooler tube assemblyPD-29
13 - 17N·m
Inlet connectorPD-29
20 - 29N·m
Oil pump assemblyPD-29
29 - 49N·m
Differential oil cooler hosePD-29
13 - 17N·m
Differential oil cooler hose (second instance)PD-29
29 - 49N·m
Differential oil cooler assembly fastenersPD-29
13 - 17N·m
Differential oil cooler hose (lower)PD-29
29 - 49N·m
Drive pinion preload N·m (kg-cm, in-lb) — With front oil sealPD-34
1.1 - 1.4N·m

With front oil seal

Total preloadPD-35
0.29N·m

Front Axle & Front Suspension

FA26 specs
Strut mounting insulator (top nut)FA-4
39 - 54N·m
Strut assembly upper mounting (to body)FA-4
88 - 108N·m
Transverse link to knuckle / front suspension memberFA-4
46 - 52N·m
Front stabilizer bracket / linkFA-4
39 - 49N·m
Tension rod bracket (to body)FA-4
39 - 49N·m
Tension rod bracket (to tension rod)FA-4
39 - 49N·m
Tension rod (to front suspension member)FA-4
88 - 108N·m
Wheel bearing lock nutFA-6
147 - 216N·m
Adjusting pinFA-7
124 - 143N·m
Lock nutFA-8
37 - 46N·m

Steering tie-rod lock nut

Wheel nutFA-9
98 - 118N·m
Wheel bearing lock nutFA-9
147 - 216N·m
Wheel bearing lock nutFA-11
147 - 216N·m
Cap nut (strut top, center)FA-14
59 - 78N·m
Strut mounting insulator nuts (upper 3 nuts)FA-14
39 - 54N·m
Stabilizer connecting rod upper nutFA-14
124 - 143N·m
Front suspension member to body boltsFA-14
88 - 108N·m
Transverse link rear bracket boltFA-14
46 - 52N·m
Transverse link to suspension member boltFA-14
88 - 108N·m
Transverse link ball joint nutFA-14
20 - 29N·m
Knuckle spindle to strut boltFA-14
88 - 108N·m
Stabilizer bracket boltFA-14
39 - 49N·m
Tension rod bracket boltFA-14
39 - 49N·m
TurningFA-18
0.49 - 3.43N·m
Wheel bearing lock nutFA-20
147 - 216N·m
TurningFA-20
0.49 - 3.43N·m

Rear Axle & Rear Suspension

RA34 specs
Spring upper seat / Dust cover mounting boltRA-4
88 - 98N·m
Lower link bolt (inner, upper)RA-4
69 - 88N·m
Lower link bolt (inner, lower / right side)RA-4
69 - 88N·m
Upper link rear boltRA-4
77 - 98N·m
Upper link rear bolt (second location)RA-4
77 - 98N·m
Small bracket bolt (top area, right)RA-4
16 - 19N·m
Suspension member mounting bolt (small)RA-4
43 - 55N·m
Suspension member mounting bolt (large)RA-4
98 - 118N·m
Lower arm bolt (upper location)RA-4
77 - 98N·m
Lower arm bolt (lower location)RA-4
9 - 12N·m
Wheel bearing lock nutRA-6
235 - 314N·m
Adjusting pinRA-7
69 - 88N·m

Camber adjustment tighten

Wheel bearing lock nutRA-9
235-314N·m
Wheel nutRA-9
98-118N·m
Axle housing boltRA-9
78 - 98N·m
Wheel bearing lock nutRA-10
235 - 314N·m

Installation

Side flange mounting boltRA-13
34 - 44N·m
Wheel bearing lock nutRA-13
235 - 314N·m
16 - 19RA-19
16 - 19N·m
18 - 24RA-19
18 - 24N·m
69 - 88RA-19
69 - 88N·m
43 - 55RA-19
43 - 55N·m
77 - 98RA-19
77 - 98N·m
49 - 69RA-19
49 - 69N·m
21 - 26RA-19
21 - 26N·m
98 - 118RA-19
98 - 118N·m
9 - 12RA-19
9 - 12N·m
71 - 88RA-19
71 - 88N·m
89 - 108RA-19
89 - 108N·m
34 - 44RA-19
34 - 44N·m
235 - 314RA-19
235 - 314N·m
Ball joint — TurningRA-23
0.5 - 3.4N·m

Lower ball joint inspection.

Wheel bearing lock nutRA-25
235 - 314N·m
TurningRA-25
0.5 - 3.4N·m

Brake System

BR27 specs
Flare nutBR-4
15 - 18N·m

Brake-line flare nuts.

Connecting boltBR-4
17 - 20N·m

Brake hose / connecting bolts.

Pedal bracket to bulkheadBR-6
16 - 22N·m

Top fastener of pedal bracket.

Fulcrum shaft / lower-bracket fasteners (×2)BR-6
8 - 11N·m

Two locations on bracket.

Stop lamp switchBR-6
12 - 15N·m

Switch to bracket.

A.S.C.D. cancel switchBR-6
12 - 15N·m

Switch to bracket.

Booster mounting nuts (×4)BR-8
8 - 11N·m

Two values shown — both 8–11 N·m.

Air bleederBR-13
7 - 9N·m
Connecting bolt (hose)BR-13
17 - 20N·m
Pin / main pin boltBR-13
22 - 31N·m
Torque member fixing boltBR-13
72 - 97N·m
Air bleederBR-18
7 - 9N·m
Pin boltBR-18
22 - 31N·m
Connecting bolt (hose)BR-18
17 - 20N·m
Spring washer / lever assemblyBR-18
25 - 29N·m
Cable stayBR-18
26 - 35N·m
Torque member fixing boltBR-18
38 - 52N·m
Air bleederBR-23
7 - 9N·m
Connecting bolt (hose)BR-23
17 - 20N·m
Pin / guide pinBR-23
31 - 41N·m
Torque member fixing boltBR-23
38 - 52N·m
Front-sensor bracket bolt(s)BR-35
18 - 26N·m

Sensor bracket to strut / knuckle (two locations on the figure).

Front-sensor bracket bolt (lower)BR-35
11 - 16N·m

Lower bracket bolt.

Rear-sensor wire-clamp boltBR-35
4.3 - 5.9N·m

Sensor harness clamp.

Rear-sensor mounting boltBR-35
18 - 26N·m

Sensor body to differential carrier.

Drive pinion nutBR-35
186 - 294N·m

Companion-flange retention — see PD section.

Actuator-bracket fasteners (×2 locations)BR-36
19 - 25N·m

Bracket-to-body fasteners.

Steering System

ST38 specs
Steering wheel retaining nutST-10
29 - 39N·m
Lower joint pinch bolt(s)ST-10
24 - 29N·m
Column-to-body mounting boltsST-10
13 - 18N·m
Bracket / clamp retaining bolts (multiple)ST-12
13 - 18N·m
Lower joint pinch bolt(s)ST-12
24 - 29N·m
Tilt adjusting nutST-13
4 - 5N·m

Step a).

Gear housing mounting bracket boltsST-15
24 - 29N·m
Tie-rod outer socket castle nutST-15
29 - 39N·m
Gear and linkage assembly boltsST-15
88 - 108N·m
Pipe connector — Low-pressure sideST-15
27 - 39N·m
Pipe connector — High-pressure sideST-15
15 - 25N·m
Tie-rod outer socket nut — InitialST-16
29 - 39N·m

Then tighten further to align cotter-pin hole.

Tie-rod outer socket nut — MaximumST-16
49N·m

Do not exceed.

Rear housing cover boltsST-18
16 - 21N·m
Adjusting-screw lock nutST-18
39 - 59N·m
Gear housing tube fittingST-18
20 - 26N·m
End cover assemblyST-18
59 - 74N·m
Tie-rod inner socketST-18
78 - 98N·m
Tie-rod outer socket (lock nut)ST-18
29 - 39N·m
Tie-rod adjustment lock nutST-18
37 - 46N·m
Step 4 — Adjusting screw initialST-25
4.9 - 5.9N·m
Step 5 — Adjusting screw retightenST-25
0.05 - 0.20N·m
Step 8 — Adjusting screw finalST-25
4.9 - 5.9N·m
Step 12 — Average rotating torque ±100°ST-25
0.8 - 1.3N·m

[(Max + Min) × 0.5].

Step 12 — Maximum torque increment ±100°ST-25
0.4N·m
Step 12 — Maximum rotating torque outside ±100°ST-25
1.9N·m
Step 12 — Maximum torque increment outside ±100°ST-25
0.6N·m
Tie-rod outer ball joint — RotatingST-26
0.29 - 2.94N·m
Tie-rod inner ball joint — RotatingST-26
7.4N·m

or less

Bracket / case fasteners (×2 locations)ST-28
16 - 21N·m
Bracket / pivot fastenersST-28
31 - 42N·m
Connector bolt (flow-control valve)ST-28
49 - 69N·m
ConnectorST-28
69 - 78N·m
Adjusting bar bracket fasteners (×2 locations)ST-28
14 - 18N·m
Pulley nutST-28
54 - 68N·m
Bracket fastenersST-28
27 - 35N·m
Suction pipe / casing boltsST-28
14 - 18N·m
Rear cover boltsST-28
31 - 42N·m

Body

BF16 specs
Bumper reinforcement to body (positions A-G)BF-6
43 - 55N·m
Energy-absorber / inner fastenersBF-6
25 - 32N·m
Hood adjustment / hinge / bumper-rubber bracketBF-7
21 - 26N·m
Bumper assembly mounting bolts and nuts (CS102 area)BF-7
13 - 16N·m
Back-door hinge fasteners (hinge-back door and hinge-body)BF-8
21 - 26N·m
Back door hinge fastenersBF-9
13 - 16N·m
Trunk lid striker / lockBF-9
43 - 55N·m
Bumper assembly mounting bolts and nutsBF-9
13 - 16N·m
Door adjustment / hinge / outside-handle / glass-stopper bolts (multiple locations)BF-10
5.1 - 6.5N·m
Inside-handle / regulator-assembly adjustment fastenersBF-10
13 - 16N·m
Hinge-body fastenersBF-11
21 - 26N·m

Door at hinge-body.

Striker fastenersBF-11
13 - 16N·m
Recliner pivot / slide-rail-to-floor (front and rear brackets)BF-25
43 - 55N·m
Reclining handle / side-bracket fastenersBF-25
21 - 26N·m
Seat-frame inner fastenerBF-25
25 - 32N·m
Rear-seat striker / seat-back adjustment fastenersBF-26
13 - 16N·m

Heater & Air Conditioner

HA19 specs
AHA-30
24/27N·m
BHA-30
22/24N·m
CHA-30
17/19N·m
—HA-30
-N·m
Expansion-valve fittings (top-left inset)HA-30
-N·m
AHA-31
24/27N·m
BHA-31
-N·m
CHA-31
17/19N·m
—HA-31
-N·m
Compressor mounting bolts (two outer)HA-32
44 - 54N·m
Compressor main mount boltHA-32
69 - 78N·m
Thermal protectorHA-44
10 - 15N·m
Lock nutHA-44
29 - 39N·m
Center boltHA-44
9.1 - 11.8N·m
Thermal protectorHA-47
15 - 18N·m
Shaft seal assembly boltsHA-47
20 - 24N·m
Coil mounting screw / bracketHA-47
3 - 4N·m
Magnet coil mounting boltHA-47
4 - 6N·m
Center boltHA-47
15 - 18N·m

Electrical System

EL8 specs
Through-boltEL-27
3.9 - 5.4N·m
Pulley assembly nutEL-27
83 - 108N·m
Wiper arm mounting bolt torque (driver side)EL-68
3.8 - 5.1N·m
Wiper arm mounting bolt torque (passenger side)EL-68
3.8 - 5.1N·m
Front wiper arm nutEL-70
17 - 23N·m
Rear wiper arm nutEL-70
13 - 18N·m
S.M.J. retaining boltEL-107
3 - 5N·m
BoltEL-107
3 - 5N·m

Standard Bolts Reference

From GI-20 — Tightening torque for standard bolts without lubricant

4TM6
Hex Head5.1 N·m
Hex Flange6.1 N·m
4TM8
Hex Head13 N·m
Hex Flange15 N·m
4TM8
Hex Head13 N·m
Hex Flange16 N·m
4TM10
Hex Head25 N·m
Hex Flange29 N·m
4TM10
Hex Head25 N·m
Hex Flange30 N·m
4TM12
Hex Head42 N·m
Hex Flange51 N·m
4TM12
Hex Head46 N·m
Hex Flange56 N·m
4TM14
Hex Head74 N·m
Hex Flange88 N·m
7TM6
Hex Head8.4 N·m
Hex Flange10 N·m
7TM8
Hex Head21 N·m
Hex Flange25 N·m
7TM8
Hex Head22 N·m
Hex Flange26 N·m
7TM10
Hex Head41 N·m
Hex Flange48 N·m
7TM10
Hex Head43 N·m
Hex Flange51 N·m
7TM12
Hex Head71 N·m
Hex Flange84 N·m
7TM12
Hex Head77 N·m
Hex Flange92 N·m
7TM14
Hex Head127 N·m
Hex Flange147 N·m
9TM6
Hex Head12 N·m
Hex Flange15 N·m
9TM8
Hex Head29 N·m
Hex Flange35 N·m
9TM8
Hex Head31 N·m
Hex Flange37 N·m
9TM10
Hex Head59 N·m
Hex Flange70 N·m
9TM10
Hex Head62 N·m
Hex Flange74 N·m
9TM12
Hex Head98 N·m
Hex Flange118 N·m
9TM12
Hex Head108 N·m
Hex Flange137 N·m
9TM14
Hex Head177 N·m
Hex Flange206 N·m

Search Manual

Search pages, specs, and procedures