Inspection and Adjustment — Service Data and Specifications (S.D.S.)
FA-20spec tableWheel turning angle *3 applies to Europe L.H.D. model; *4 applies to Except Europe L.H.D. model. Unladen condition defined as: tankful of fuel, radiator coolant and engine oil full, spare tire, jack, hand tools, mats in designated position.
SERVICE DATA AND SPECIFICATIONS (S.D.S.)
Inspection and Adjustment
WHEEL ALIGNMENT (Unladen*1)
| Specification | Value |
|---|---|
| CamberUnladen | -1°25' to 5'degree |
| CasterUnladen | 5°55' - 7°25'degree |
| Toe-in (Total)Unladen | 0 - 2 (0 - 0.08)mm (in)0' - 12'degree |
| Kingpin inclinationUnladen | 12°25' - 13°55'degree |
| Front wheel turning angle — Full turn *2 inside/outsideEurope L.H.D. model (*3) | 36° - 40°/32° *3degree |
| Front wheel turning angle — Full turn *2 inside/outsideExcept Europe L.H.D. model (*4) | 39° - 43°/33° *4degree |
CamberUnladen
-1°25' to 5'degree
CasterUnladen
5°55' - 7°25'degree
Toe-in (Total)Unladen
0 - 2 (0 - 0.08)mm (in)0' - 12'degree
Kingpin inclinationUnladen
12°25' - 13°55'degree
Front wheel turning angle — Full turn *2 inside/outsideEurope L.H.D. model (*3)
36° - 40°/32° *3degree
Front wheel turning angle — Full turn *2 inside/outsideExcept Europe L.H.D. model (*4)
39° - 43°/33° *4degree
NOTE
*1: Tankful of fuel, radiator coolant and engine oil full. Spare tire, jack, hand tools, mats in designated position.
*2: On power steering models, wheel turning force (at circumference of steering wheel) of 98 to 147 N (10 to 15 kg, 22 to 33 lb) with engine idle.
*3: Europe L.H.D. model
*4: Except Europe L.H.D. model
WHEEL BEARING
| Specification | Value |
|---|---|
| Wheel bearing axial end play | 0.03 (0.0012) or lessmm (in) |
| Wheel bearing lock nut | 147 - 216N·m |
Wheel bearing axial end play
0.03 (0.0012) or lessmm (in)
Wheel bearing lock nut
147 - 216N·m
LOWER BALL JOINT
| Specification | Value |
|---|---|
| Swing force (Measuring point: cotter pin hole of ball stud) | 7.8 - 55.9 (0.8 - 5.7, 1.8 - 12.6)N (kg, lb) |
| Turning | 0.49 - 3.43N·m |
| Vertical end play | 0 (0)mm (in) |
Swing force (Measuring point: cotter pin hole of ball stud)
7.8 - 55.9 (0.8 - 5.7, 1.8 - 12.6)N (kg, lb)
Turning
0.49 - 3.43N·m
Vertical end play
0 (0)mm (in)
WHEEL RONOUT (Radial and lateral)
WHEEL RONOUT (Radial and lateral)
Aluminum wheel mm (in)
Radial runout0.3 (0.012) or less
Lateral runout0.3 (0.012) or less
Steel wheel mm (in)
Radial runout0.5 (0.020) or less
Lateral runout0.8 (0.031) or less